65810WAR-6K
The Sperry Marine X-Band Radar Scanner Unit comes provided with 4, 6 and 8 ft antenna, and 10kW or 25kW options.
+65 6909 8211/13, info[at]globalshipspares[dot]com (Asia)
info-europe[at]globalshipspares[dot]com (EU)
Categories
Filter By
Filter By
Products
074807 REV C
The first digital marine gyrocompass of its type to be designed as a single unit and of unparalleled compactness in a polyurethane hard foam housing, the NAVIGAT X MK 1 digital gyrocompass has a low weight. This...
074799 REV B
The NAVIGAT X MK 2 Digital Gyro Compass system provides a cost-effective solution that satisfies the international carriage requirements for a type-approved marine gyrocompass.
Vision Master FT ECDIS
The VisionMaster FT radar/ECDIS from Sperry Marine provides intelligent functions for safe navigation, exceeding IMO requirements for additional safety at sea. Based on the VisionMaster FT software, this particular...
049050-0000
Sperry supporting liquid, used on gyrocompass Navigate X MK1 and MK2.
020672-0000-000
This main board is the main control of gyro system. Two ship supply input to mainboard. One AC supply output 26Vac from transformer which step down AC ship supply from 230Vac or 115Vac via link and other 24Vdc direct...
T65801805-4
During removal and refitting of the mounting bracket, take care not to damage the teeth on the pulse disc assembly that run between opto-couplers mounted on the rear of the Pulse Bearing PCB. Before re-tightening the...
4991-3000
Inside the gyrosphere container, the gyrosphere floats in a supporting fluid with a buoyancy that is a little greater than its weight, a bearing cup at the bottom of the recess is pressed against the centering pin and...
T91003765-6
Sperry x-band motor gear, Standard speed unit 250VA.High-speed unit 370VA.This motor is a 3-phase electronically commutated DC motor. The motor commutation drive signals are supplied by the Motor Drive PCB, which can...
074571-0000-000
This is a mercury gyrosphere only used in mercury type container.
T65801801-10
A control board housed in the Transceiver. It controls the Modulator, Magnetron and sends signals to the Display to indicate when the magnetron has fired a pulse.
074859-0000-000
This is a Type 4894-AD Terminal Box, used for Type 5016 Bearing Repeater Compass.
T65825816
This PSU board in x-band transceiver, provide high voltage DC is present to all primary power components. This voltage is present even when the unit is switch OFF. The high voltage is only removed if the unit is...
074834-0000-005
The 4891 Universal Digital Repeater is to display live heading (HDG).
T65900812-3
This SC3 card is an assembly in the motherboard. It need a cable assy to connect to PCIO TSS port. It converts raw video into digitize video for PC to process the radar echo.
074880-0001-000
This is a Type 5016 Bearing repeater compass. Does not come with Type 4894-AD terminal box.
T65830642-3
Turning unit contains the Antenna rotation motor, the microwave rotary joint, and may contain an integral Transceiver.
T65801811-9
This board is use on the X-band Scanner Unit, signal is fed to the Power Supply Unit and via the Turning Unit On/Off and Input PCB to the Motor Drive PCB to start the antenna rotating.
T65830812-6
The principal function of the Modulator PCB is to generate an 8kV,8A negative pulse to drive the cathode of the magnetron. An SCR is used to resonantly charge a Pulse Forming Network (PFN) to -1200V from the-600V...
T65801813-8
On the Scanner Unit, signal is fed, via the Power Supply Unit, to the Input PCB and, via TSB 10, to the Scanner Control Unit to start the antenna rotating.
TVH-03-2001
Sperry Marine BME Slave Connection Unit.
4923-AA
The NAVITWIN III Heading Management System displays and monitors a minimum of one and a maximum of three heading sources (2 gyrocompass headings and 1 magnetic heading) from a variety of heading sensors.
65900667-3C
Sperry Marine VMFT Control Panel is used in all Sperry Marine stand alone radar systems.
65847A
This is a Sperry Marine radar serial interface unit.