65810WAR-6K
The Sperry Marine X-Band Radar Scanner Unit comes provided with 4, 6 and 8 ft antenna, and 10kW or 25kW options.
+65 6909 8211/13, info[at]globalshipspares[dot]com (Asia)
info-europe[at]globalshipspares[dot]com (EU)
Categories
Filter By
Filter By
Products
Filter By
Vision Master FT ECDIS
The VisionMaster FT radar/ECDIS from Sperry Marine provides intelligent functions for safe navigation, exceeding IMO requirements for additional safety at sea. Based on the VisionMaster FT software, this particular...
T65801805-4
During removal and refitting of the mounting bracket, take care not to damage the teeth on the pulse disc assembly that run between opto-couplers mounted on the rear of the Pulse Bearing PCB. Before re-tightening the...
T91003765-6
Sperry x-band motor gear, Standard speed unit 250VA.High-speed unit 370VA.This motor is a 3-phase electronically commutated DC motor. The motor commutation drive signals are supplied by the Motor Drive PCB, which can...
7000 109-141
The Saab R4 Navigation Sensor should be connected to the included antenna, which in the GPS configuration is a MGA-2 GPS antenna and in the DGPS configuration is a MGL-4 combined GPS/Beacon antenna.
T65801801-10
A control board housed in the Transceiver. It controls the Modulator, Magnetron and sends signals to the Display to indicate when the magnetron has fired a pulse.
T65825816
This PSU board in x-band transceiver, provide high voltage DC is present to all primary power components. This voltage is present even when the unit is switch OFF. The high voltage is only removed if the unit is...
T65900812-3
This SC3 card is an assembly in the motherboard. It need a cable assy to connect to PCIO TSS port. It converts raw video into digitize video for PC to process the radar echo.
T65830642-3
Turning unit contains the Antenna rotation motor, the microwave rotary joint, and may contain an integral Transceiver.
T65801811-9
This board is use on the X-band Scanner Unit, signal is fed to the Power Supply Unit and via the Turning Unit On/Off and Input PCB to the Motor Drive PCB to start the antenna rotating.
T65830812-6
The principal function of the Modulator PCB is to generate an 8kV,8A negative pulse to drive the cathode of the magnetron. An SCR is used to resonantly charge a Pulse Forming Network (PFN) to -1200V from the-600V...
T65801813-8
On the Scanner Unit, signal is fed, via the Power Supply Unit, to the Input PCB and, via TSB 10, to the Scanner Control Unit to start the antenna rotating.
TVH-03-2001
Sperry Marine BME Slave Connection Unit.
65900667-3C
Sperry Marine VMFT Control Panel is used in all Sperry Marine stand alone radar systems.
65847A
This is a Sperry Marine radar serial interface unit.
DG43NB
This is a Sperry Marine VMFT original manufacturer approved motherboard. Supports CD Rom, video card, hard disk, sc2 or cs3 card, rams, USB port, VGA port.
65900614-3E
Sperry VMFT Trackball is used on all Sperry Marine stand alone unit systems.
65901AN-7A
This is a Sperry Marine VMFT processor unit running on either Windows XP or Windows 7.
65800700
This no/off switch is to control scanner control unit.
65837AA-AJ
Sperry Marine scanner control unit is to control scanner on/off.
T65830616-7
This Receiver Unit is used in Sperry Marine S-band transceiver unit.
T65810812-6
The principal function of the Modulator PCB is to generate an 8kV,8A negative pulse to drive the cathode of the magnetron. An SCR is used to resonantly charge a Pulse Forming Network (PFN) to -1200V from the-600V...
T65900800-6A
The PCIO Board has three high speed serial input (38400 baud) and six low speed serial inputs (4800 baud).
Communication to the processor is via an embedded USB hub (TSU). Video and data to the scan converter (SC)...
T91003746-4
Performance Monitor unit, which warns the operator of reduce radar performance.
May be integral with the turning unit.